First Alert Professional Fa560 Manual

FA168CPS / FA168CPSSIA

FA148CP / FA148CPSIA

Security Systems

Congratulations on your ownership of a First Alert Professional Security System. You've made a wise decision in choosing it, for it. This manual for procedures for using these features. The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to give you enough. Arming your ATP ALARMS First Alert System. • Ensure thatthe greenReady Light is illuminated. The display should noly read AC (simply to show that there is AC power to the system. • If the greenRead y Light is not on, the display willNOTread READY. Lynx: L3000 and below, Lynx REN. First Alert: FA 215, FA260, FA270, FA560, FA570. System must be “READY TO ARM” to enter the “Manual Dialer Test Mode”. Enter your master code + 5 + 1. If “Test” or “CC” is displayed on your keypad, the panel will attempt to send a Test Report to the monitoring center.

READY

READY

1

IMPORTANT!

PROPER INTRUSION PROTECTION

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in amulti-levelbuilding.

In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Central Monitoring Station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines).

EARLY WARNING FIRE DETECTION

Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72). These recommendations can be found on page 45 of this manual.

SYSTEM COMPATIBILITY NOTICE

Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's keypad or other communicating bus if Honeywell has not approved such device for use with your security system. Use of any such unauthorized device may cause damage or compromise the performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have been thoroughly tested to ensure optimum performance when used with your Honeywell security system.

About This Manual

This manual is a step-by-stepguide that will acquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and provides clearstep-by-stepinstructions for normal and emergency procedures. Keep this manual in a convenient place so that you can refer to it as necessary.

– 2 –

Table of Contents

System Overview

Introduction

Congratulations on your ownership of a First Alert Professional Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. This system provides:

•Three forms of protection: burglary, fire* and emergency

•At least one keypad which provides control of system and displays system status

•Various sensors for perimeter and interior burglary protection

•Smoke or combustion detectors* designed to provide early warning in case of fire. Your system may also have been programmed to automatically send alarm or status messages over the phone lines to a Central Monitoring Station.

*Commercial installations and some residential systems may not include fire protection – check with your installer.

NOTE: The features and procedures described in this manual apply to the FA168CPS/FA168CPSSIA (referred to as FA168CPS) and FA148CP/FA148CPSIA (referred to as FA148CP) security systems. Differences are noted where applicable.

System Basics

Burglary Protection

•Several modes of burglary protection: Stay, Night-Stay,Away, Instant, Maximum. STAY: arms perimeter zones only and entry delay is on

INSTANT: same as STAY, except entry delay is off

NIGHT-STAY:arms perimeter zones and selected interior zones; entry delay on AWAY: arms perimeter and all interior zones, entry delay is on

MAXIMUM: same as AWAY, except entry delay is off

•You can BYPASS selected zones while leaving the rest of the system armed.

•CHIME mode alerts you to the opening of protected doors and windows while the system is disarmed.

Fire Protection

•Fire protection is always active (if installed) and an alarm sounds if a fire condition is detected

•If programmed, you can manually initiate a fire alarm using the keypad.

•Refer to the Fire Alarm System section for information regarding fire protection, smoke detectors and planning emergency exit routes.

Security Codes

•You were assigned a 4-digitsecurity code (master code) during installation.

•Use your security code when arming and disarming the system, and when performing other system functions.

•Other users can be assigned different security codes, each with different authority levels, which define the system functions a particular user can perform.

–5 –

System Overview (Continued)

Zones and Partitions

•The system sensing devices have been assigned to various “zones,” which are specific areas of protection (e.g., front door, kitchen window, etc.).

•Zone numbers are displayed at the keypad when an alarm or trouble condition occurs on a sensor.

•Partitions (FA168CPS) provide two independent areas of protection, with each partition containing a group of zones that can be armed and disarmed without affecting other zones or users.

•Partitioned systems (FA168CPS) can include a common zone area, which is an area shared by users of both partitions (such as a lobby in a building).

Arming, Step-Armingand Disarming Burglary Protection

•The system must be armed before the burglary protection can sense intrusions.

•To arm your system, enter your user code followed by the desired arming key.

•If programmed, you can press the [#] key in place of your security code when arming the system (e.g., instead of entering your 4-digitsecurity code +[3-STAY]to arm the system in STAY mode, you can press [#] +[3-STAY]).

•You can use the step-armingkey, if programmed, to arm the system, which lets you arm the system in one of three modes by simply pressing the key repeatedly.

•To disarm the system, enter your security code then press the [OFF] key.

Alarms

•When an alarm occurs, both the keypad and external sounders will sound, and the keypad will display the zone(s) causing the alarm.

•If your system is connected to a Central Monitoring Station, an alarm message is also sent. (Delayed Reporting Note: Message reporting is delayed 30 seconds by default to reduce false alarms. If desired, this delay can be removed or can be increased to 45 seconds. See your installer if you want the delay time changed.)

•To stop the alarm sounding, simply disarm the system.

Memory of Alarm

•When an alarm condition occurs, the keypad displays the number(s) of the zone(s) that caused the problem, and displays the type of alarm (e.g., “FIRE”).

•The message remains displayed even after disarming the system, but can be cleared with another “off” sequence.

Function Keys

•The “A”, “B”, “C”, and “D” keys on the keypad can be programmed to perform various functions.

•Functions include: activate a Panic alarm; arm the system; provide step arming; switch lights on/off; send a message to a pager; display Time/Date; start a Macro.

Scheduling

•Your system can be programmed to automatically perform certain functions (e.g., arm the system) at a predetermined time each day.

System Overview (Continued)

Phone Access

•If included, a Phone Module permits you to access the system via a touch-tonephone, eitheron-premisesor bycalling-inwhen away.

•You can receive synthesized voice messages over the telephone regarding the status of the security system.

•You can arm and disarm the system and perform most function commands remotely via the telephone, with voice confirmation provided after each command.

•Refer to the Phone Access User's Guide supplied with the Phone Module for information regarding the use of this feature.

Paging Feature

•If programmed, the system can automatically send certain system condition messages to up to four (FA168CPS) or two (FA148CP) pagers.

•The system can also automatically alert a pager if the system has not been disarmed by a certain time (e.g., can let you know a child has not arrived home).

•You can also manually send a message to designated pagers.

Using the Voice Message Center (if Voice Keypad is installed)

The Voice Keypads feature a voice message center that lets you record and playback one message.

•The message can be up to 2.5-minuteslong

•The message remains in the keypad’s memory until a new message is recorded.

•The volume control of the message is adjustable.

•Refer to the procedures below when using the Message Center functions.

Message Center Functions

About The Keypads

General Information

Your keypads allow you to control all system functions. The keypads feature the following:

•A telephone style (digital) keypad

•Liquid Crystal Display (LCD) which shows the nature and location of all occurrences

•Built-insounder which will sound during alarms and troubles. The sounder also 'beeps' during certain system functions and when depressing any of the keys (to acknowledge the key press).

•Backlighting of the LCD display windows. Backlighting turns on when any key is pressed, and when opening an entry/exit door while the system is armed. This feature is helpful when a keypad is located in a dimly lit area.

IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.

Your keypads are functionally the same, but may have different types of displays, depending on the type installed with your system.

Alpha Display 2-linealpha display keypads feature a2-line,32-characteralphanumeric LCD which can display system messages in friendly English. These keypads can also be programmed with custom zone descriptors.

Fixed-Word Display Fixed-Worddisplay keypads are functionally identical to Alpha display keypads, but the LCD display usespre-designatedwords to identify the nature and location of occurrences.

Voice Keypads Voice Keypads (if installed), are functionally the same as other keypads, except that these keypads can provide the following:

•Voice announcements of system status (see Checking for Open Zones section)

•Voice chime, which can alert you to the opening of doors and windows while the system is disarmed (see Voice Chime in

Chime mode section)

•Message center, which lets you record and playback messages (see Using the Voice Message Center in the

System Overview section).

About The Keypads (Continued)

Fixed-WordDisplay Keypad

Functions of the Keypads

NOTE: The functions printed directly on the keys indicate their primary purpose; the functions printed under some of the keys (shown in brackets under the respective key), indicate their alternate or secondary purpose.

DISPLAY WINDOW

Alpha Display Keypads: 2-line,32-characterLiquid Crystal Display (LCD) keypads that display protection point identification, system status, and messages.

Fixed-Word Display Keypads: Display protection zone ID and system status messages usingpre-designatedwords in the LCD display area.

1 OFF Disarms burglary portion of the system,

silences alarms and audible trouble indicators, and clears visual display after problem's correction. [RECORD] On Voice keypads, used in conjunction with the FUNCTION and VOICE keys to record up to a2.5-minutemessage.

2 AWAY Arms the entire burglary system,

perimeter and interior.

[VOLUME] On Voice keypads, used in conjunction with the FUNCTION and desired volume control keys↑ [3] or↓ [6] to adjust the volume of a recorded message or voice system status.

3 STAY Arms perimeter portion of burglary

system only. Interior protection is not armed, allowing movement within premises without causing an alarm. If pressed twice in succession, arms system in NightStay mode.

[PLAY] On Voice keypads, used in conjunction with the FUNCTION and VOICE keys to play the recorded message.

[ ↑ ] On Voice keypads, used in conjunction with the FUNCTION and VOLUME keys to raise the message and voice system status volume.

4 MAXIMUM Arms the entire burglary system,

perimeter and interior, but without entry delay feature. Entering via an entry/exit door will cause an alarm.

5 TEST Tests the system and alarm sounder if

disarmed. Refer to Testing The System section for test procedures.

8 CODE Used to assign additional security codes

and attributes for other users of the system.

6 BYPASS Removes individual protection zones

from being monitored by the system.

[ ↓ ] On Voice keypads, used in conjunction with the FUNCTION and VOLUME keys to lower the message and voice system status volume.

7 INSTANT Arms in manner similar to the STAY

mode, but without the entry delay feature.

9 CHIME Turns CHIME mode on and off. When on,

the opening of windows or doors while the system is disarmed sounds 3 beeps at the keypad(s).

KEYS 0–9:Used to enter your security code(s).

READY Used to display open protection zones.

[STATUS]: On Voice keypads, one press of the STATUS key annunciates the current system status. Pressing the STATUS key a second time annunciates and displays system and/or zone faults (if they exist).

0 [VOICE] On Voice keypads, enables the

RECORD, VOLUME and PLAY functions.

#This key can be used for 'Quick Arming' of the

system without use of a security code (if programmed). [FUNCTION] On Voice keypads, enables the desired voice or volume function.

FUNCTION KEYS: Keys A, B, C, D may have been set for certain functions, such as panic (emergency) functions. For details, see theFunction Keys section.

ARMED LED INDICATOR: (RED) Lit when the system has been armed.

READY LED INDICATOR: (GREEN) Lit when the system is ready to be armed (no faults present). While the system is disarmed, this indicator will go on and off as protection zones are closed and opened.

MESSAGE LED INDICATOR: (RED) On Voice keypads, flashes red when message waiting or lights red (steady) when in record mode.

MIC: On voice keypads, microphone for Message Center recordings.

INTERNAL SPEAKER: Thebuilt-inspeaker mimics the alarm sounder during alarms, and will also 'beep' during certain system functions. The speaker also provides voice playback for any recorded messages.

Functions of the Keypads (Continued)

SPEAKER

Voice-capable2-lineAlpha keypad

IMPORTANT!

•When entering codes and commands, sequential key depressions must be made within 4-5seconds of one another. If4-5seconds elapse without a key depression, the entry will be aborted and must be repeated from its beginning. Be sure to observe this precaution when performing any of the procedures in this manual.

•If you make a mistake while entering a security code, stop, press the [ ] key, and then start over. If you stop in the middle while entering a code, and then immediately start the entry over, an erroneous code might be entered.

–11 –

Entry/Exit Delays

Exit Delay

Exit delay gives you time to leave through the designated exit door(s) without setting off an alarm. Exit delay begins immediately after arming your system in any arming mode and Alpha Display keypads display the message “You May Exit Now.” When “You may exit now” disappears, the system is fully armed. If programmed, a slow beeping will sound during the exit delay period until the last 10 seconds, which then changes to fast beeping (alerting you to the end of exit delay). If you cannot leave by this time, you should stop, disarm the system, and start over to avoid a false alarm.

Exit Delay Restart. If you wish to open the entry/exit door to let someone in after arming STAY, you canre-starttheexit delay at any time –simply press the [ ]key, then let that person in. The system automaticallyre-armswhen exit delay expires, which avoids having to disarm the system and thenre-armit again. In addition, when the system is armed AWAY, reopening and closing the entry/exit door before exit delay time expires (e.g., reentering to get a forgotten item) will reset the exit delay time once.

Entry Delay

Entry Delays give you time to disarm the system when you re-enterthrough the designated entrance door. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the keypad to disarm the system.

You must disarm the system before the entry delay period ends, or an alarm will occur. The keypad beeps during the entry delay period, reminding you to disarm the system. The beeps stop when a code is entered, but will restart after about 15 seconds if an invalid code is entered.

You can also arm the system with no entry delay at all by using the INSTANT or MAXIMUM arming modes. These modes provide greater security while on the premises or while away for extended periods of time.

You can also arm the system with no entry delay at all by using the INSTANT or MAXIMUM arming mode. This mode provides greater security while on the premises or while away for extended periods of time.

See your installer for your delay times.

Partition 1____________________________________________________________________________

NOTE: Entry/Exit times set for partition 1 also apply to the common zone (FA168CPS).

Partition 2 (FA168CPS)_______________________________________________________________

Entry/Exit Delays (Continued)

Exit Alarms

Exit Error Conditions

Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted before exit delay expires and remains faulted (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message 'ALARM CANCELED ' or 'CA' is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the Central Monitoring Station.

To clear the exit error condition, the open zone must be made intact; to clear the display, enter your code plus OFF.

If you do not disarm the system before the entry delay ends and the faulted zone remains open, the alarm sound continues and an 'exit alarm' message is sent to the Central Monitoring Station (after the installer-programmeddial delay expires). The message 'EXIT ALARM' or 'EA' is displayed on the keypad, along with a zone number indicating the faulted zone. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time.

An “exit alarm” also results if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay.

Your system may have been programmed for this feature to minimize false alarms sent to the Central Monitoring Station. Ask your installer if 'Exit Alarm' is active in your system. If so, check this box.

FA168CPSSIA/FA148CPSIA: The Exit Error condition works the same as described above, except that in addition to the “EXIT ALARM” message, a “zone alarm” message is also sent to the Central Monitoring Station. In addition, if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay, a “Recent Closing” condition occurs instead of the “exit alarm.” Refer to the next paragraph for details.

“Recent Closing” Condition (FA168CPSSIA/FA148CPSIA)

A Recent Closing condition is similar to the Exit Error condition described above, but occurs if an entry/exit door or interior zone is faulted within two minutes after the initial exit delay expires. If you disarm the system within the two minutes, the alarm sound stops and the message 'ALARM CANCELED ' or 'CA' is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the Central Monitoring Station.

If you do not disarm the system within two minutes and the faulted zone remains open, the alarm sound continues and a “recent closing” and a “zone alarm” message are sent to the Central Monitoring Station (after the installer-programmeddial delay expires). The alarm message along with a faulted zone number is displayed on the keypad. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time.

Checking For Open Zones

Using the [ ] Key

Before arming your system, all protected doors, windows and other protection zones must be closed or bypassed, otherwise the keypad will display a 'Not Ready' message.

Use the READY key to display all faulted zones, making it easier for you to identify and secure any open zone.

1.Press [ ] (do not enter code first) to display faulted zones.

2.Secure or bypass the zones displayed.

3.The keypad’s READY indicator lights when all protection zones have been either closed or bypassed.

4.Arm the system as desired.

Alpha Display:

DISARMED

HIT FOR FAULTS

Fixed-WordDisplay:

Zone no. and “NOT READY”

Voice Status: Voice Keypads (if installed), can announce system status and faulted zones (up to 3 zone descriptors) if the Voice Status feature is turned on.

To turn the Voice Status feature on/off: # + 0 + 2 + 4

(also turns on Voice Chime mode; see Chime mode section)

To announce Status: Press [#] FUNCTION + [0] VOICE + [ ] STATUS key. (Announces current system status; e.g., “Disarmed Ready to Arm.”)

To announce faults Press [#] FUNCTION + [0] VOICE + [ ] STATUS + [ ] again.and Status: (Announces up to three faulted zones with their zone

descriptors, if programmed.)

Arming the System

Stay Mode: Arms Perimeter Only, Entry Delay On

•Used when you want to arm the system with persons staying inside (or if you have pets that are moving throughout the premises).

•The perimeter sensors are armed, but interior sensors are left disarmed.

•Exit delay begins (you can leave through the entry/exit door, if desired).

•An alarm sounds if any protected window or non-entry/exitdoor is opened.

•You may otherwise move freely within the premises.

•Persons entering later can enter through an entry/exit door, but they must disarm the system within the entry delay period to avoid sounding an alarm.

Night-StayMode: Arms Perimeter Only, Plus Selected Zones

•Use Night-Staymode to provide increased security while staying inside.

•Arms same as Stay mode, but also arms pre-selectedinterior sensors (programmed by your installer), while other interior sensors are left disarmed.

•Persons entering later can use entry/exit doors but they must disarm the system and must not violate any of the programmed interior zones to avoid sounding an alarm.

•IMPORTANT: WhenNight-Staymode is on, the selected interior zones are armed and cause an alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an alarm, you must disarm the system before any activity takes place in those interior zones.

Instant Mode: Arms Perimeter Only, Entry Delay Off

•Used when staying inside and do not expect anyone to use an entry/exit door.

•Arms same as Stay mode.

•An alarm sounds immediately if any protected perimeter window or any door is opened, including entry/exit doors.

•IMPORTANT: Arming in this mode greatly increases the chance of false alarms. Use extreme care in selecting this mode of arming.

Away Mode: Arms Entire System, Entry Delay On

•Used when nobody will be staying inside (including pets).

•The entire system (interior and perimeter) is armed.

•Exit delay begins letting you leave through the entry/exit door.

•An alarm sounds if a protected window or any door is opened, or if any movement is detected inside your premises.

•You can reenter through an entry/exit door, but you must disarm the system within the entry delay period to avoid sounding an alarm.

Maximum Mode: Arms Entire System, Entry Delay Off

•Used when leaving the premises for extended periods (e.g., vacation).

•Arms same as Away mode, but entry delay is off.

•An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

–15 –

Arming the System

Arming Commands

Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed.

Modes of Arming

† Arming Ding: In addition to the keypad beeps, the external sounder emits a short “ding” sound after arming, if programmed to do so. The ding confirms that the system is armed, and may occur immediately after the command or be delayed (until arm/disarm report is sent or exit delay expires). Ask your installer about how this feature is set for your system.

Quick Arming

If 'Quick Arming' was programmed by the installer, the [#] key can be pressed in place of the security code when arming the system in any of its arming modes (except NightStay). However,the security code must always be used when manually disarming the system.

Function Key Arming

For any arming command, a function key may have also been programmed for your system. If so, you can press and hold the appropriate function key for 2 seconds to arm the system. See your installer for the designated functions (see Single Button Arming section).

Refer to the Accessing Other Partitions section for information onmulti-partitionarming (FA168CPS).

Arming the System

Single Button Arming

The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for single-buttonarming. Note that while it is not necessary to use a security code for arming (by using the Quick Arm method described previously), a security code must always be used when manually disarming the system.

If Single-ButtonArming is programmed:

•A function key has been assigned to a specific type of arming: STAY mode, Night-STAYmode, AWAY mode, orSTEP-ARMING(seeStep-Armingparagraph).

•You DO NOT need to enter your security code before pressing the function key (but you always need your security code to DISARM the system).

Before arming, close all perimeter doors and windows.

1.Press and hold the assigned function key for 2 seconds (no code is required). Function keys are shown below.

2. The keypad begins beeping and displays the armed message. The red ARMED indicator also lights.

Alpha Display:

DISARMED

READY TO ARM

Fixed-WordDisplay:READY

Alpha Display:

ARMED***AWAY*** YOU MAY EXIT NOW

Fixed-WordDisplay:AWAY

Step Arming Feature

Single-Button“Step” arming may have been programmed into one of the lettered keys (A, B, C, or D). Check with your installer to see if this has been done in your system.

If Step-Armingis programmed:

•The assigned key provides a choice of three levels of security.

•The selected key can be pressed once, twice, or three times, increasing the level of security with each press, as follows

Using the Keyswitch

Using the Keyswitch

Your system may be equipped with a keyswitch for use when arming and disarming. Red and green lights on the keyswitch plate indicate the status of your system as follows:

Green Light: Lights when the system isdisarmed and ready to be armed (no open zones). If the system is disarmed and the green light is off, it indicates the system is not ready (one or more zones are open).

Red Light: Lights or flashes when system is armed in AWAY or STAY mode. See your installer for the meanings of the lit red light:

Lit Steady = system armed AWAY or

system armed STAY and exit delay has expired

Flashing = system armed STAY and exit delay timer active

Rapid flashing = an alarm has occurred (memory of alarm).

Before arming, close all perimeter doors and windows.

To arm in the AWAY mode:

Turn the key to the right for 1/2 second and release. Keypads beep twice and the red indicator lights or flashes.

To arm in the STAY mode:

Turn the key to the right and hold for longer than 1 second, then release. Keypads beep three times and the red indicator lights or flashes.

To disarm the system:

Turn the key to the right and release. The red light turns off

Disarming and Silencing Alarms

Using the [OFF] key

The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear alarm memories.

IMPORTANT: If you return and the main burglary sounder is on,DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location.

If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence.

LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.

The “READY” indicator light will be lit if all zones are secure, and the keypad will emit a single tone to confirm that the system is disarmed.

NOTE: If entry delay has started (you’ve opened the entry door), you do not need to press the OFF key; simply enter your security code. The system will disarm in about 15 seconds after the last digit of the code is entered.

Alpha Display:

DISARMED

READY TO ARM

Fixed-WordDisplay: READY

2.To Silence a Burglary Alarm and Clear a Memory of Alarm

Enter your security code. This disarms the system and silences the alarm (or warning tones of a Memory of Alarm).

Note the zone in alarm on the keypad display, and make that zone intact (close door, window, etc.). Now enter the security code plus OFF to clear the keypad’s

Memory of Alarm display.

3.To Silence a Fire Alarm and Clear Memory of Alarm

Simply press the OFF key to silence the alarm. Then enter thesecurity code plusOFF sequence to clear the keypad'sMemory of Alarm display. See theFire Alarm System section.

Bypassing Protection Zones

Using the BYPASS Key

Use this key when you want to arm your system with one or more zones intentionally unprotected.

Vent Zones: Your system may have certain windows set as “vent” zones, which are automatically bypassed if left open when arming the system (you do not need to manually bypass them). However, if a vent zone window is closedafter arming, it becomes protected and will cause an alarm if opened again while the system is armed.

When bypassing zones:

•The system must be disarmed before you can bypass zones.

•Bypassed zones are unprotected and will not cause an alarm if violated.

•The system will not allow fire zones to be bypassed.

•Zones are automatically unbypassed when the system is disarmed.

Enter the 2-digitzone number(s) for the zone(s) to be bypassed (e.g., 06, 10, 13, etc.). Single digit zone numbers must be preceded by a zero (e.g. 05, 06).

2.When finished, the keypad will momentarily display a 'Bypass' message for each bypassed zone number. Wait for all bypassed zones to be displayed.

Arm the system as usual. When armed, the arming message is displayed with “ZONE BYPASSED.” To display bypassed zones prior to arming, enter your security code and press the [6] BYPASS key.

Alpha Display:

DISARMED

HIT * FOR FAULTS

Fixed-WordDisplay:NOT READY

Alpha Display:

DISARMED BYPASS

READY TO ARM

Fixed-WordDisplay:BYPASS

ARMED: STAY

ZONE BYPASSED

Typical armed alpha display after bypassing zones.

Bypassing Protection Zones

Quick Bypass

If programmed, 'Quick Bypass' allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night.

1.+ 6 + [#]

(Security Code) BYPASS

In a few moments, all open zones will be displayed and automatically bypassed. Make sure that only those zones that you wish to leave unprotected are bypassed, and that there are no other zones unintentionally left open.

2.Wait for all bypassed zones to be displayed, then arm the system as desired.

Ask your installer if 'Quick Bypass' is active for your

system, and if so, check here:

Alpha Display:

DISARMED

HIT * FOR FAULTS

Fixed-WordDisplay:NOT READY

Alpha Display:

DISARMED BYPASS

READY TO ARM

Fixed-WordDisplay: BYPASS

Chime Mode

CHIME mode alerts you to the opening of a perimeter door or window while the system is disarmed. When Chime mode is activated:

•Three tones sound at the keypad whenever a perimeter door or window is opened.

•Interior zones do not produce a tone when they are faulted.

•Pressing the READY key will display the open protection points.

•Chime mode can be used only while the system is disarmed.

(Security Code) CHIME

The CHIME message will appear. Perimeter zones will cause a tone when faulted.

Alpha Display:

DISARMED CHIME READY TO ARM

Fixed-WordDisplay:CHIME

(Security Code) CHIME

Voice Chime: You can set the Voice Keypads (if installed) to announce faulted (opened) entry/exit or perimeter zones whenever normal Chime mode is on.

To turn Voice Chime Mode on or off: # + 0 + 2 + 4

(normal Chime mode must be on first)

When Voice Chime is on, faulted zones cause a voice status announcement, chime and display. When off, the sounder still provides chime if normal Chime mode is on.

Date and Time

Viewing the Current Date and Time

The master users can view the system time and date setting on alpha keypad. Other users can view the date/time if a function key has been programmed to do so.

+[#] + [6] [3]

(Master Code)

OR, press the function key (A, B, C, or D) for viewing current date and time, if programmed.

If one of the above keys has been programmed for the date/time display feature, place a check mark in the box beneath that key.

Setting the Date and Time

NOTE: All partitions must be disarmed before date/time can be set.

You can set the time and date by doing the following:

1.+[#] + [6] [3]

(Master Code)

2.Press [ ] when the time/date is displayed.

A cursor appears under the first digit of the hour.

To move cursor ahead, press [ ]. To go back, press [#].

•Enter the 2-digithour setting.

•Enter the 2-digitminute setting.

•Press [1] for PM or [0] for AM.

•Enter the last two digits of the current year.

•Enter the 2-digitmonth setting.

•Enter the 2-digitday setting.

3.To exit, press [ ] when cursor is at the last digit, or wait 30 seconds.

Alpha Display:

DISARMED

READY TO ARM

TIME/DATE SAT 04:04PM 10/17/00

Current time display

TIME/DATE SAT 04:04P2000/10/17

Time/date editing display

Panic Keys

Using Panic Keys

Your system may have been programmed to use special keys to manually activate emergency (panic) functions as follows:

*All panic functions send signals to the Central Monitoring Station, if connected.

To activate a Panic Function:

Press and hold down for at least 2 seconds whichever lettered key on the keypad has been programmed for the desired emergency function.

OR

Press both keys of the assigned key pair at the same time.

Alpha Display:

DISARMED

READY TO ARM

Fixed-WordDisplay:READY

Typical Panic Alpha Display:

ALARM 99

Fixed-WordDisplay:99 and ALARM

A

D

Lettered Panic Keys

PRESS BOTH KEYS OF DESIRED PAIR AT THE SAME TIME

ZONE 96

560KP-10-002-V0

See your installer and use the chart provided in the Features Programmed in Your System section to note the functions that have been programmed for your system.

Macro Key Programming & Usage

About Macro Keys

The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of commands of up to 16 keystrokes, if programmed for this function. These keystrokes, as a group, are called “macros” and are stored in the system's memory.

•Typical macro functions can include:

-Arming sequences: STAY, Night-STAY,INSTANT, or AWAY

-Bypassing particular zone(s)

-Activating relay(s) for turning on (or off) lights, fans, etc.

•Up to four (FA168CPS) or two (FA148CP) macros can be assigned – but no more than one macro to a key.

•Macros can be activated only by users with authority levels authorized to perform the macro’s function.

NOTE: The installer must activate the desired function key before macros can be assigned. See the chart at the back of this manual for the key(s) assigned for macros.

1.+ [#] + [6] + [6]

(Master Code)

2.Enter the macro number (1-4for FA168CPS;1-2for FA148CP) to be programmed at the “Select Macro?” prompt. Remember, only one macro can be assigned to each key.

Alpha Displays:

DISARMED

READY TO ARM

3.If a macro has been previously defined, the keystrokes are shown on the bottom line of the display, otherwise the display is blank.

To exit this mode (and keep the existing macro definition), press any key except the [ ] key. The system returns to normal mode.

To define a macro for the selected key, press [ ] and continue with the next prompt.

Enter the first of the series of desired commands, (do not include your master code), then press/hold the “D” key for at least two seconds to complete the first command. This key terminates each command, and appears as an “F” in the keypad display.

– 25 –

Macro Key Programming & Usage (cont.)

The keypad beeps to acknowledge your input and displays the command you entered (followed by “F”).

4.Enter the next command, followed by press/holding the “D” key for at least two seconds. The keypad beeps and displays the keystrokes entered so far.

5.Repeat until the all the desired commands (up to 16 characters including the “F”s) have been entered.

Be sure to check your keystrokes before continuing. If you made a mistake, you must start over.

6.To exit, press/hold the “D” key for at least two seconds. The display returns to system status and indicates system is ready.

Example of Macro Programming

Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an exterior light, and then (3) arm the security system in the AWAY mode. The procedures in the table that follows show you how you would program this macro:

Typical Macro Alpha Display:

MACRO PGM

6 0 2 0 3 F # 7 0 1 F 2 F

Using a Programmed Macro Key

1.Press the Macro key programmed for the desired series of commands for at least 2 seconds. The “Enter User Code” prompt appears. The prompt remains displayed for up to 10 seconds.

2.Enter your 4-digitsecurity code.

The programmed macro sequence begins automatically after the user code is entered.

Using Device Commands

About Device Commands

Your system may be set up so that it can control certain lights or other devices.

•Some devices may be automatically turned on or off by the system.

•You may be able to override automatically controlled devices using the commands described below.

•Some devices can be manually turned on or off using the commands described below.

•See your installer for a list of devices that may be set up for your system. A list of these devices is provided at the back of this manual for you to fill out.

(Security Code)

Devices associated with that device number deactivate.

Paging Feature

About Automatic Paging

Your system may be set up to automatically send alert messages to several pagers (up to four for FA168CPS, up to two for FA148CP) as certain conditions occur in your system.

•The following events can be programmed by your installer to be sent to the pagers: arming and disarming†, alarms, and trouble conditions. († reports when arming/disarming from a keypad using a security code;auto-arming/disarming,arming with assigned button, and keyswitch arming do not send pager messages.)

•You can also program the system to send an automatic pager message to alert you in the event that someone has not arrived home (disarmed the system) within a defined period of time (see the Scheduling section for details on programming a “latch key report”).

•Your installer programs the pager phone numbers and reporting events.

•The pager message consists of a 7-digitsystem status code that indicates the type of condition that has occurred.

•An optional, predefined 16-digitcharacter string can precede the7-digitsystem status code; these characters can consist of a PIN no., subscriber account no., or any additional data that you may wish to have sent to the pager.

•The pager display format is as follows:

ÈÈ

AAAAAAAAAAAAAAAA – BBB – CCCC Å 1-digitPartition No. +3-digitZone No.or User No.

Ex. 1. 9 1 1 – 1 0 0 4 = Reporting of an alarm (911) caused by a fault on zone 4 on Partition 1 (1004).

Ex. 2. 1 0 2 – 2 0 0 5 = Reporting of aclosing–systemarming (102)– by user 5 in Partition 2 (2005).

Paging Feature

Manual Paging

Your system may be set up so you can manually send a message to up to four (FA168CPS) or two (FA148CP) pagers.

• Your installer programs the paging function key and the pager phone numbers.

• Pressing the paging keys sends the message 9 9 9 – 9 9 9 9 to the selected pager.

•This message could mean “call home”, “call your office”, or any other prearranged meaning.

•See the Paging chart at the back of this manual for details of the paging setup for your system.

1.Hold pager key 2 seconds then press pager no.(1-4).*

Press and hold the programmed Paging Key for at least 2 seconds (wait for beep), then press the pager number representing the pager intended to receive the message.

2.The recipient, on seeing the 999–9999message, will understand the prearranged meaning of this signal.

*If no number is pressed, the message is sent to pager 1. Pagers1-4for FA168CPS series;1-2for FA148CP series

Alpha Display:

DISARMED

READY TO ARM

Fixed-WordDisplay:READY

999-9999

Pager Display

Latch Key Paging

You can program a schedule that causes a pager report to be sent if the system is not DISARMED by the scheduled time (see Scheduling section, event “03”). For example, a working parent might want a message to be sent to a pager if their child did not arrive home from school and disarm the system by a certain time.

If programmed, the message that is sent is: 7 7 7 – 7 7 7 7 .

Security Codes & Authority Levels

About Security Codes

Your installer assigned a master code that is used to perform all system functions. In addition, you can assign different security codes for use by other users (FA168CPS provides 47 additional codes; FA148CP provides 31 additional codes).

•Only the System Master and Partition Master can assign security codes to users.

•Users are identified by 2-digituser numbers and arepre-assignedto either partition 1 or partition 2 (FA168CPS).

•Only the System Master can change user partitions.

•In addition to a security code, each user is assigned various system attributes.

•Security codes can be used interchangeably within a partition when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the Guest code and Arm Only code described below.

•Security code programming involves these steps:

1.Choose a user number from the set of users assigned to the partition in which the user will be operating, and assign a 4-digitsecurity code.

2.Assign an authority level to that user.

3.Assign other attributes as necessary (see attributes on the next page).

NOTE: The factory settings are designed to meet most normal user situations. Therefore, the only step you usually need to do when adding users is assign a user number (from the partition’spre-assigneduser numbers) and a security code.

Authority Level Definitions

Authority levels define the system functions a particular user can/cannot perform.

Security Codes & Authority Levels (Cont.)

How to Assign Security Codes and Attributes

The following lists the various command strings for adding security codes and attributes

Refer to the User Setup chart at the back of this manual for factory assignments of user attributes and to keep a record of user programming.

NOTE: Partition Master codes (FA168CPS only) apply only to those user numbers previously assigned (by the system master/installer) to the partition master’s partition.

Accessing Other Partitions (FA168CPS)

(GOTO Command and Multi-PartitionArming)

About Accessing Partitions

Each keypad is assigned a default partition for display purposes, and will show only that partition's information.

•If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. Refer to the GOTO section.

•If the user is authorized, that user can arm other partitions. Refer to the MultiPartition Arming section.

The following table shows the relationship of the keypads in each partition when system is armed and disarmed.

When both partitions are disarmed, the keypad in each partition displays zone status for its partition only. The common zone keypad shows the status in that zone only. See Condition 1 above.

When partition 1 is disarmed and partition 2 is armed, the keypad in partition 1 shows the status of partition 1 and the common zone. Partition 2 will display the status of partition 2only. See Condition 2 above.

When partition 1 is armed and partition 2 is disarmed, the keypad in partition 1 shows the status of partition 1 only. Partition 2 will display the status of partition 2and the common zone. See Condition 3 above.

As long as any one of the two partitions is disarmed, the common zone will always be disarmed. The common zone will be armed only when both partition 1 and 2 are armed. See Condition 4 above.

Accessing Other Partitions (Continued)

Using the GoTo Command

If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command.

•You must use an Alpha keypad to access another partition.

•Keypads automatically return to their original partition after 30 seconds with no keypad activity.

1. + [ ] + partition number (0,1,2,3)

(Security Code; only applies if user has access to other partitions)

0 = return to keypad’s original partition.

1 = partition 1; 2 = partition 2; 3 = common zone The keypad beeps to confirm the partition change.

2.The keypad remains in the new partition until directed to go to another partition, or until it automatically returns to the original partition.

The active partition number is displayed in the upper left portion of screen, if the option is programmed.

Alpha Display:

1 DISARMED READY TO ARM

Fixed-WordDisplay:Green LED lit

Alpha Display:

2 DISARMED READY TO ARM

Fixed-WordDisplay:Green LED lit

Multi-PartitionArming

Some users can be given Multi-Partitionarming ability by being assigned to both partitions when programming user attributes.

When attempting to arm multi-partitions:

•You must use an Alpha keypad.

•The system arms only if all partitions are “ready to arm.”

•If any partition is “not ready,” the system does not arm at all.

•You can use the GOTO command to bypass open zones before arming.

•If any partition is already armed when global arming is attempted, that partition remains in its existing armed state.

+ [0] + arm command (see list below)

(Security Code)

Multi-PartitionArming Commands

2 = arms all partitions AWAY

3 = arms all partitions STAY

33 = arms all partitions NIGHT-STAY

4 = arms all partitions MAXIMUM

7 = arms all partitions INSTANT

1 = disarms all partitions

Alpha Display:

1 DISARMED READY TO ARM

Fixed-WordDisplay:Green LED lit

Accessing Other Partitions (Continued)

Common Zone Operation

Ask your installer if a 'common zone' was assigned. If so, check

this box

Your system may have been set up to use a common zone, which is an area shared by users of both partitions, such as a foyer or lobby. If so, please note the following:

•The common zone will sound and report alarms only when both partitions are armed. If only one partition is armed, the system ignores faults on the common zone.

•Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to arm unless the common zone is first bypassed or the fault is corrected.

•Faults on the common zone are displayed on common partition keypads, and will also appear on another partition’s keypad when the alternate partition is armed.

•Either partition can clear and restore the common zone after an alarm.

•Entry/exit time for the common zone is the same as for partition 1.

Scheduling

About Scheduling

The system provides end-userschedules (programmable by master/installer only), which can control various types of events.

•Each schedule causes a defined event to start and stop (when appropriate) at a specified time.

•Schedules can be set to automatically repeat at various intervals.

•Schedules can be set for random starting, if desired.

•FA168CPS provides up to 16 user schedules; FA148CP provides up to 4 user schedules.

Alpha Displays:

3. Enter the desired2-digitevent number from the following list.

00 = clear the scheduled event

01 = turn a programmed output on or off

(see Using Device Commands section for a list of output device numbers used in your system)

02 = set a user access schedule for one or more users

(see Security Codes section for an explanation of access groups)

03 = send a “latch-key”report to a pager if the system is not disarmed by a specified time; message sent is“777-7777.”

04 = automatically arm the system in STAY mode at a specified time 05 = automatically arm the system in AWAY mode at a specified time 06 = automatically disarm the system at a specified time

07 = Display the word “REMINDER” at a specified time (if selected, the keypad beeps every 30 seconds beginning when the word “REMINDER” is first displayed, and the display alternates with the normal keypad display about every 4-5seconds. To stop the beeps and cancel the display once it starts, simply press any key).

Press [ ] to continue.

4.For event number “01,” enter the output number associated with this schedule.

Otherwise, this prompt is skipped.

Press [ ] to continue to the “Start” prompt shown on the next page.

– 35 –

Scheduling (continued)

5.For event number “02,” enter the access group

number. Otherwise, this prompt is skipped. Press [ ] to continue to the “Start” prompt below.

6.For event numbers “03-07,”enter the partition number to be armed or disarmed.

0 = arm all; 1 = partition 1; 2 = partition 2; 3 = arm common

Otherwise, this prompt is skipped.

Press [ ] to continue to the “Start” prompt.

7.Enter the event’s start time and days of week. Hour = 00-12;minute =00-59

AM = 0; PM = 1

Days = Position the cursor under the desired days using the [ ] key to move forward, then press “1” to

select the day. Press [ ] to continue.

8.If applicable, enter the event’s stop time and days of week (applies only to event numbers 01, 02, and 03).

Refer to step 7 for available entries. Press [ ] to continue.

9.Enter the desired repeat option. 0 = no repeat

1 = repeat schedule weekly

2 = repeat schedule biweekly (every other week)

3 = repeat schedule every third week

4 = repeat schedule every fourth week

e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To make a schedule that runs for one week then stops,

select everyday with a repeat count of 0. Press [ ] to continue.

10.For event number 01 (output on/off), select the desired randomize option. 0 = no; 1 = yes

If selected, the schedule times will vary within 60 minutes of the “hour” time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it

will start anytime between 6:00 and 6:59 p.m. Press [ ] to continue.

GROUP NUMBER

X

PARTITION

X

START SMTWTFS

HH:MMAM 1000000

STOP SMTWTFS HH:MMAM 1000000

REPEAT OPTION 0-4X

RANDOMIZE 0=NO 1=YES X

Event Logging Procedures

About Event Logging

The system records various events in a history log, which can be viewed by the master user using an Alpha Display keypad.

•The Event Log holds up to 100 (FA168CPS) or 50 (FA148CP) events.

•Events are displayed in chronological order, from most recent to oldest.

•When the log is full, the oldest event is replaced by the logging of any new event.

Viewing the Event Log

(Master Code)

2.The system displays the most recent event as follows: event number, type of event (see table of codes below), zone or user number (depending on type of event) partition in which event occurred, time and date of the event’s occurrence.

3.Pressing [ ] displays previous events (back in time). Pressing [#] displays events forward in time.

4.Exit by pressing any key other than [ ] or [#].

Alpha Displays:

DISARMED

READY TO ARM

001 E441 U001 P1 12:34AM 01/02/00

Understanding the Type of Event Displayed

If the event code is preceded by an E (as in the above display), it means that the event is new and ongoing; if preceded by an R, it means the event has been restored.

See your installer for more detailed information regarding the meanings of these codes

Testing the System (To Be Conducted Weekly)

About Testing the System

Test mode allows each protection point to be checked for proper operation.

•The keypad sounds a single beep about every 30 seconds as a reminder that the system is in the Test mode.

•Alarm messages are not sent to your Central Station while Test mode is on.

1Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on if all zones are intact (i.e., all protected windows, doors, etc. are closed.

The Dial test (option “1”) is intended for the installer and should not be used unless directed to do so by your Security System Representative.

3.Listen. The external sounder should sound for about 1 second then turn off. If the sounder does not sound, CALL FOR SERVICE. The “Test in Progress” display appears only on the keypad that started the test.

Alpha Displays:

DISARMED

READY TO ARM

1 = DIAL, 0 = WALK

TEST IN PROGRESS

4.Fault zones. Open each protected door and window in turn and listen for three beeps from the keypad. Identification (zone number or zone description) of each faulted protection point should appear on the display. The display clears when the door or window is closed.

5.Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the detector should appear on the display when it is activated. The display clears when no motion is detected.

Note that if wireless motion detectors are used, there is a 3-minutedelay between activations. This is to conserve battery life.

6.Test all smoke detectors, following the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is experienced with any protection point (no confirming sounds, no display), call for service immediately.

When all protection points have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad.

(Security Code)

If the test mode is inadvertently left active, it automatically turns off after 4 hours. During the final five minutes, the keypad will emit a double beep every 30 seconds.

Trouble Conditions

'Check' and 'Battery' Displays

*Not all systems use wireless sensors.

The wordCHECK on the keypad's display, accompanied by a 'beeping' at the keypad, indicates a trouble condition in the system.

To silence the beeping for these conditions, press any key.

1.A display of 'CHECK' and one or more zone numbers indicates that a problem exists with the displayed zone(s) and requires your attention. Determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence (security code plus OFF key) twice. If the display persists, CALL FOR SERVICE.

Note: A display ofCHECK 70 on Alpha Display keypads indicates that the wiring connection to the external sounder is at fault (opened or shorted), and you should CALL FOR SERVICE. See “BELL FAILURE” on next page. A display ofCHECK 90 indicates that RF interference may be impeding the operation of wireless sensors* in the system. See “Rcvr Jam” on next page.

2.If there are wireless sensors* in your system, the CHECKcondition may also be caused by some change in the environment that prevents the wireless receiver from receiving messages from a particular sensor. CALL FOR SERVICE if this occurs.

IF YOU CANNOT CORRECT A 'CHECK' DISPLAY, CALL FOR SERVICE.

TYPICAL 'CHECK' DISPLAYS

C H E C K 0 6

B E D R O O M W I N D O W

– 39 –

Trouble Conditions (Continued)

Other Trouble

Displays

*Any “beeping” that accompanies a trouble display can be stopped by depressing any key on the keypad or by entering an OFF sequence (code + OFF)

**Not all systems use wireless sensors.

Words or letters in parentheses ( ) are those that are displayed on Alpha Display keypads.

In The Event Of Telephone Operational Problems

In the event of telephone operational problems, disconnect the control from the phone line by removing the plug from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of your phone lines. If the regular phones work correctly after the control has been disconnected from the phone wall jack, the control has a problem and you should immediately call for service. If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made only by authorized service (see the LIMITED WARRANTY statement for information on how to obtain service).

Maintaining Your System

Taking Care of

Your System

Silencing Low

Battery Warning

Tones at the

Keypad

The components of your security system are designed to be as maintenance-freeas possible. However, to make sure that your system is in reliable working condition, do the following:

1.Test your system weekly.

2.Test your system after any alarm occurs.

You can silence the keypad’s warning tones by pressing the OFF key, but the keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a 'good battery' signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the sensor is not activated, the display will automatically clear within approximately 1 hour.

Replacing

Batteries in

Wireless Sensors

Wireless sensors may not have been used in your security system

IMPORTANT:

Use only batteries recommended by your installer as replacement.

Each wireless sensor in your system has a 9-voltor3-voltbattery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless keypad and displays a low battery message*. (A low battery in a portable wireless keypad is detected as soon as one of its keys is pressed, and displayed as00.).Battery-operatedsmoke detectors with a low battery also emit a single 'chirp' sound approximately once every20–30seconds.

Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4years of service.3-voltlithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation.

* The low battery message comes on as a warning that battery replacement in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational.

Routine Care • Treat the components of your security system as you would any other electrical equipment. Do not slamsensor-protecteddoors or windows.

•Keep dust from accumulating on the keypad and all protective sensors, particularly on motion sensors and smoke detectors.

•The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units.

Fire Alarm System (If Installed)

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. A FIRE message will appear at your Keypad and remain on until you silence the alarm (see below for silencing fire alarms).

* Temporal pulse sounding is produced for Fire alarms, as follows: 3 pulses–pause–3pulses–pause–3pulses–pause. . . ,repeated.

TYPICAL FIRE EMERGENCY DISPLAYS

1.You can silence the alarm at any time by pressing the OFF key (the security code is not needed to silence fire alarms). To clear the display, enter your code and press theOFF key again (to clear Memory of Alarm).

2.If the Keypad's FIRE display does not clear after the second OFF sequence, smoke detectors may still be responding to smoke or heat producing objects in their vicinity. Investigate, and should this be the case, eliminate the source of heat or smoke.

3.If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds.

When the problem has been corrected, clear the display by entering your code and pressing the OFF key.

Smoke Detector Depending on the type of smoke detectors in your system, it may beReset necessary to 'reset' the smoke detectors after a fire alarm has been

turned off. Check with your installer. This 'reset' is accomplished at a keypad, as follows:

Enter Security Code*, then press the [1] key (* except “arm only” user).NOTE: During smoke detector reset, “FAULT xx” appears (about six seconds) and should disappear if the detector is clear.

Fire Alarm System (Continued)

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

1.Should you become aware of a fire emergency before your smoke or heat detectors sense the problem, go to your nearest keypad and manually initiate an alarm by pressing the panic key assigned for FIRE emergency for 2 seconds. If a key pair has been assigned for fire, press both keys at the same time. See the Using the Panic Keys section below for further details.

2.Evacuate all occupants from the premises.

3.If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.

4.If no flames or smoke are apparent, investigate the cause of the alarm. The zone number(s) of the zone(s) in an alarm condition will be displayed at the keypad.

A key or key pair may have been assigned for manually initiating a FIRE alarm. See the Panic Keys section for key assignments.

For convenience, indicate the key or key pair assigned for fire below.

First Alert Fa260 Keypad Manual

Individual Keys

A B C

Press the individual key assigned for firefor 2 seconds.

OR

Key Pairs

DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM

AC

95

ALARM

FIRE

– 44 –

Fire Alarm System (Continued)

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

National Fire Protection Association Recommendations on Smoke Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72) noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics.

In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.

BEDROOM

Fire Alarm System (Continued)

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

Emergency Evacuation

8.Establish a common meeting place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house — many die going back

Quick Guide to Basic System Functions

Summary of Audible/Visual Notifications

Fixed-WordDisplay Keypads

*If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency issteady ring.

–48 –

Summary of Audible/Visual Notifications

Alpha Display Keypads

* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency issteady ring.

Regulatory Statements and Warnings

NOTE: This is a “Grade A” Residential System

RADIO FREQUENCY EMISSIONS

Federal Communications Commission (FCC) Part 15

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet Appareil numérique de la classe B est conforme à la norme NMB-003du Canada.

TELEPHONE/MODEM INTERFACE

FCC Part 68

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.

This equipment uses the following USOC jack: RJ31X

This equipment may not be used on telephone-company-providedcoin service. Connection to party lines is subject to state tariffs. This equipment ishearing-aidcompatible.

Industry Canada

NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate.

Ringer Equivalence Number Notice:

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Regulatory Statements (Continued)

Industrie Canada

AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessusn’empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordementslui-même;il doit avoir racours à un service d’inspection des installations électriques, ou à un électricien, selon le cas.

AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

Charts of Your System’s Features

† Features marked with a dagger apply to the FA168CPS only.

Charts of Your System’s Features

User Setup

The following chart will help keep track of system users. Copies should be distributed to the partition 1 and partition 2 (if applicable) masters for their records.

To program a user attribute:

Enter system/partition master code + [8] + user no. + “#” command listed in column heading…

† Partitions apply to the FA168CPS only.

Charts of Your System’s Features

User Setup (continued)

Enter system/partition master code + [8] + user no. + “#” command listed in column heading…

† Users 34-49apply to FA168CPS only; user 33 is partition 2 master for FA168CPS, and the last user for FA148CP.

Charts of Your System’s Features

Paging Setup

Schedules: master code + [#] + [6] [4]. (†FA168CPS can use schedules01-16;FA148CP can only use schedules01-04.)

Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week

List of Output Devices

(† FA168CPS can use devices 01-16;FA148CP can only use devices01-08;both can use trigger devices 17/18.)

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

Fa560 Keypad

17

18

– Notes –

– Notes –

– Notes –

– Notes –

OWNER’S INSURANCE PREMIUM CREDIT REQUEST

This form should be completed and forwarded to your homeowner’s insurance carrier for possible premium credit.

A. GENERAL INFORMATION:

Insured’s Name and Address:

FA168CPS / FA148CP Other ______________________________________________________

(circle the appropriate model number)

C. POWERED BY: A.C. With Rechargeable Power Supply

continued on other side

– 61 –

OWNER’S INSURANCE PREMIUM CREDIT REQUEST (cont.)

G. ADDITIONAL PERTINENT INFORMATION:

– 62 –

LIMITATIONS OF THIS SYSTEM

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM

While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:

•Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device.

•Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

•Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

•A user may not be able to reach a panic or emergency button quickly enough.

•While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.

•Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease.

•Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impairedpeople or waken deep sleepers.

•Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

•Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.

•This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.

Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

ONE YEAR LIMITED WARRANTY

Honeywell International Inc., acting through its First Alert Professional business ('Seller'), 165 Eileen Way, Syosset, New York 11791, warrants its First Alert Professional security equipment (the 'product') to be free from defects in materials and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security equipment or the Seller for product repair.

This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No increase or alteration, written or verbal, to this warranty is authorized.

149 Eileen Way Syosset, New York 11791

Copyright © 2003 Honeywell International Inc.

ÊK5309-5V4DŠ

K5309-5V410/04 Rev. B

• Categories

  Top types

  Audio & home theatre

  Cameras & camcorders

  Computer cables

  Computer components

  Computers

  Data input devices

  Data storage

  Networking

  Print & Scan

  Projectors

  Smart wearables

  Software

  Telecom & navigation

  TVs & monitors

  Warranty & support

  other →

  Top brands

  Acer

  AEG

  Aeg-Electrolux

  Asus

  Canon

  Casio

  Electrolux

  HP

  LG

  Nikon

  Panasonic

  Philips

  Samsung

  Sony

  Yamaha

  other →

  Top types

  Infotainment

  Musical instruments

  Video games & consoles

  other →

  Top brands

  Acer

  AEG

  Asus

  Dometic

  Electrolux

  HP

  LG

  Panasonic

  Philips

  Progress

  Samsung

  Sharp

  Sony

  ZANKER

  Zoppas

  other →

  Top types

  Binding machines

  Boards

  Calculators

  Correction media

  Desk accessories & supplies

  Drawing supplies

  Equipment cleansing kit

  Folders, binders & indexes

  Laminators

  Mail supplies

  Paper cutters

  Sorters

  Storage accessories for office machines

  Typewriters

  Writing instruments

  other →

  Top brands

  Bosch

  Canon

  Casio

  Craftsman

  Dell

  Epson

  Fujitsu

  HP

  KitchenAid

  LG

  Panasonic

  Philips

  Samsung

  Sharp

  Smeg

  other →

  Top types

  Bedding & linens

  Cleaning & disinfecting

  Do-It-Yourself tools

  Domestic appliances

  Home décor

  Home furniture

  Home security & automation

  Kitchen & houseware accessories

  Kitchenware

  Lighting

  other →

  Top brands

  AEG

  Aeg-Electrolux

  Bauknecht

  Candy

  Electrolux

  HP

  Indesit

  LG

  Panasonic

  Philips

  Progress

  Samsung

  Sony

  Whirlpool

  Zanussi

  other →

  Top types

  Bags & cases

  Children carnival costumes

  Clothing care

  Clothing hangers

  Dry cleaners

  Fabric shavers

  Men's clothing

  Tie holders

  Ultrasonic cleaning equipment

  Watches

  Women's clothing

  other →

  Top brands

  Braun

  Casio

  Delta

  Garmin

  Huawei

  Indesit

  LG

  Mitsubishi Electric

  Philips

  Radio Shack

  SEVERIN

  Sony

  V7

  Velleman

  ZyXEL

  other →

  Top types

  Air Handlers

  Boom Lifts

  Compact Excavator

  Elevators

  Excavators

  Finishers

  Front End Loaders

  Noise Reduction Machine

  Oxygen Equipment

  Robotics

  Scrubber

  Spreader

  Tractor

  Trash Compactor

  Welding System

  other →

  Top brands

  AEG

  Aeg-Electrolux

  Asus

  Canon

  Casio

  Electrolux

  HP

  LG

  Nikon

  Panasonic

  Philips

  Samsung

  Sony

  Whirlpool

  Yamaha

  other →

  Top types

  Blood pressure units

  Electric toothbrushes

  Epilators

  Feminine hygiene products

  Foot baths

  Hair trimmers & clippers

  Makeup & manicure cases

  Men's shavers

  Personal paper products

  Personal scales

  Shaver accessories

  Skin care

  Solariums

  Teeth care

  Women's shavers

  other →

  Top brands

  AEG

  Aeg-Electrolux

  Bosch

  Canon

  Casio

  Electrolux

  KitchenAid

  LG

  Panasonic

  Philips

  Samsung

  Sony

  Whirlpool

  Yamaha

  Zanussi

  other →

  Top types

  Hot beverage supplies

  other →

  Top brands

  other →

  Top types

  Cars

  Electric scooters

  Motor vehicle accessories & components

  Motor vehicle electronics

  Motorcycles

  Motorhomes

  Offroad Vehicle

  Scooters

  Utility Vehicle

  other →

  Top brands

  AEG

  Aeg-Electrolux

  Bosch

  Canon

  Casio

  Craftsman

  Electrolux

  LG

  Panasonic

  Philips

  Samsung

  Sharp

  Sony

  Yamaha

  Zanussi

  other →

  Top types

  Baby bathing & potting

  Baby furniture

  Baby safety

  Baby sleeping & bedding

  Baby travel

  Feeding, diapering & nursing

  Toys & accessories

  other →

  Top brands

  AEG

  Asus

  Bosch

  Canon

  Casio

  Electrolux

  HP

  LG

  Panasonic

  Philips

  Samsung

  Sony

  Whirlpool

  Yamaha

  Zanussi

  other →

  Top types

  Bicycles & accessories

  Bubble machines

  Camping, tourism & outdoor

  Fitness, gymnastics & weight training

  Martial arts equipment

  Skateboarding & skating

  Smoke machines

  Sport protective gear

  Target & table games

  Water sports equipment

  Winter sports equipment

  other →

  Top brands

  Craftsman

  Daikin

  Emerson

  Epson

  Frigidaire

  Harbor Freight Tools

  HP

  Miele

  Panasonic

  Philips

  ProForm

  Samsung

  Sennheiser

  Weider

  Yamaha

  other →

  Top types

  Pet hair clippers

  other →

  Top brands

  Andis

  other →

  Top types

  Pill Reminder Device

  Stairlifts

  other →

  Top brands

  Alber

  Bruno

  E-PIL

  Minivator

  Savaria

  other →